Important information related to RIFF Box eMMC support

[Tedjo]

How can I do it in riff if there is no KLMAG4FEJA-A002 selection ...

I have only riff and no other tool for direct emmc for now ..

I have backup it but read by other emmc selection ...

I have a problem after place KLMAG4FEJA-A002 to p3100
I can not write other RPMB bin file to this partition
boot1 boot2 and user partition has no problem at all
p3100 was working now but I can not repair imei in this case ...
repair imei keep on error for this emmc chips .

[topher05]

thanks...................

[apiruk]

thank you

[eliasnakl]

thank you

[devthakur81]

Open serial port...OK
Connecting to the RIFF Box...OK

Getting RIFF Box Info...OK
RIFF Box Firmware Version: RECOVERY (RIFFBOX1)

Connecting to the Updates Server...OK
Downloading new Firmware from Server...OK

Setting Update Mode...

blinking green light only

[mtk6572s4clone]

Open serial port...OK
Connecting to the RIFF Box...OK

Getting RIFF Box Info...OK
RIFF Box Firmware Version: RECOVERY (RIFFBOX1)

Connecting to the Updates Server...OK
Downloading new Firmware from Server...OK

Setting Update Mode...

blinking green light only

Open serial port...OK
Connecting to the RIFF Box...OK

Getting RIFF Box Info...OK
RIFF Box Firmware Version: RECOVERY (RIFFBOX1)

Connecting to the Updates Server...OK
Downloading new Firmware from Server...OK

Setting Update Mode... ------>

disconnect and reconect the box

[benbyben]

@Legija

can you post the pinout from eMMC/SD & GPIO port for Riffbox II?

[mtk6572s4clone]

@Legija

can you post the pinout from eMMC/SD & GPIO port for Riffbox II?

Hi men, I don't have the RIFF2, you can to try it (check with a multimeter in continuity mode the GROUND (GND) points identified,
also check the voltages, if are correct, the pinout is fine



Greetings.

[benbyben]

2v8 is GND, 2v8 is over 2v8

here is the pinout, thx to Multi com:

[benbyben]

i modify the emmcpro adapter and now ist working great with DAT0-DAT3 :

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.80V, SD_CLK Frequency is 51 MHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x15
OEM/Application ID ................... 0x00
Product Name ......................... "K2U00M"
Package .............................. BGA
User Area Partition Size ............. 0x000747C00000 Bytes (29.12 GB)
Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... No Boot
Chip Revision ........................ 0.5
Multimedia Card Revision ............. 1.5 (eMMC v4.41)
Serial Number ........................ 0x9C084CC4
Memory Manufacturing Date ............ May, 2012

[brahim1977]

Thank You

[mtk6572s4clone]

i modify the emmcpro adapter and now ist working great with DAT0-DAT3 :

Ok men

[ashokmadivala]

can i use smartgsm 4in1 adopter?

[mtk6572s4clone]

can i use smartgsm 4in1 adopter?

Hi, I only find it thanks to Javohir

Unlock Forum - RIFF Box support forum

greetings

[master-ce]

thank all